We have warehouse in some countries, check as bellows. 1 x 8GB USB Flash drive. 4 Axis PLC Controller 500KHz off-line.RMHV2.1 is the 4 axis and 4 axes motion controller which has been researched and developed by RATTM MOTOR CNC for four years. The control period of each position is only 4 milliseconds, with a high control precision.
The highest uniaxial output pulse is 500KHz and the pulse width can be adjusted. It supports the common stepper motor and servo motor. Numerical control system adopts the ARM+FPGA design framework. The ARM can finish the part of human-computer interface and code analysis and the FPGA can finish the part of underlying algorithm and control pulse generate, with the reasonable design, reliable control and easy operation. The panel layout structure of.The CNC MOTION SYSTEM Controller can be finished only by 17 keys and it supports the FANUC with high universality to be compatible with G code set. This manual introduces the operation method of the. The machine tool and the operation procedure of the machine tool. By lots of graphical representation and examples, the uses can quickly learn to use the. 1.2 Performance parameter of Product 1 Ordinary digital input interface of 16-circuitoptocoupler coupling isolation 2 Ordinary digital input interface of 3-circuit optocoupler coupling isolation 3 Output interface of 0-10V spindle control port with analog quantity(can be modified as PWM output); 4 Support the 4 axis stepper motor control, the highest control pulse output of single axis is 500KHz; 5 ARM9 main control chip; 6 FPGA core algorithm chip; 7 4.3 inches TFT screen, resolution ratio: 480272; 8 17 operational keys; 9 The main control equipment is 18V-32V power input, the current capacity is required not to be lower than 0.5A; 10 Support the USB flash disk to read the G code, and the size of G codefile has no requirement; 11 Be equipped with MPG port and support digital display MPG as well as support the general MPG in the market. 12 Support the panel key with single-axis manual operation, manual step and CONToperation; 13 Support the operation of quickly specify the running position; 14 Support the multi coordinate systems (with automatically saving function in case of power cut); 15 Support the function of saving data automatically after power down (press the start to automatically save the data in the operation, automatically save the data after power down) 1.3 Outward Appearance, Structure and Size. Adopts the embedded shell structure, which can punch a square hole on the equipment cabinet and then embed this equipment in the squire hole. Use two locking mechanism from the inside can fix this equipment on the equipment cabinet, with easy installation.
The panel size of the product is 163mm102mm5mm; The size of main body is 156mm93mm45mm; The size of square hole installed on the equipment cabinet is 156mm93mm. The front of the product is 17 user keys and 1 4.3and 480272 LSD (Liquid Crystal Display), and the reverse side is input signal, spindle control, stepper/ servo control, MPG and other four sets of interfaces as well as USB interface and power interface. Please look at the reference picture 1-3 and picture 1-4 in detail.This USB Interface is the standard USB socket of A-type, attached a 50cm USB extension cord with installation lugs. CNC system and position control of various mechanical devices, mainly for CNC machine tools and various mechanical zero correction and signal division. 100 times per revolution slightly cracking point, 100 pulses per revolution output, holding the handle of the panel and all-metal high-grade design.
Metal code disc, high precision, good texture. Easy installation, shaped thin, ultra-light. Voltage, single-ended, differential in three output options provide 100PPR pulse output options.Driver output type, anti-interference ability, long-distance transmission. Oil, water, dust-proof design (grade IP65) spiral stretch 20 million guaranteed. Novelty, easy to move, interference, load capacity. Full plastic shell, insulation, high strength, anti-oil seal design. With × 1, × 10, × 100 third gear ratio, enabling 4-12 axis magnification switch. With the control switch, emergency stop switch optional, easy to operate. For CNC machine tools, printing machinery, numerical control equipment. OFF, X, Y, Z, 4. Please give us the opportunity to resolve any problem when you have, we concern your problem and we will try our best to resolve it. When you have the parcel, and not satisfied the goods or it is other problem like as broken, pls tell us the detail reason and provide the photos. Item must be in it's original condition and no physical damage.
Customers satisfaction is very important to us. The item "GB&EU4 Axis 500KHZ Stand Alone Motor CNC Motion Controller + Pendant Handwheel" is in sale since Thursday, November 11, 2021. This item is in the category "Business, Office & Industrial\Industrial Automation & Motion Controls\PLCs & HMIs\PLC Peripheral Modules\PLC Servo Control Modules".The seller is "infoshine15" and is located in Frankfurt. This item can be shipped to United Kingdom, European Union member countries.