3 Output interface of 0-10V spindle control port with analog quantity(can be modified as PWM output). 4 Support the 4 axis stepper motor control, the highest control pulse output of single axis is 500KHz. 5 ARM9 main control chip. 6 FPGA core algorithm chip.
7 4.3 inches TFT screen, resolution ratio: 480272. 9 The main control equipment is 18V-32V power input, the current capacity is required not to be lower than 0.5A. 10 Support the USB flash disk to read the G code, and the size of G codefile has no requirement.
11 Be equipped with MPG port and support digital display MPG as well as support the general MPG in the market. 12 Support the panel key with single-axis manual operation, manual step and CONToperation.
13 Support the operation of quickly specify the running position. 14 Support the multi coordinate systems (with automatically saving function in case of power cut). 15 Support the function of saving data automatically after power down (press the start to automatically save the data in the operation, automatically save the data after power down). 1.3 Outward Appearance, Structure and Size. Adopts the embedded shell structure, which can punch a square hole on the equipment cabinet and then embed this equipment in the squire hole.Use two locking mechanism from the inside can fix this equipment on the equipment cabinet, with easy installation. The panel size of the product is 163mm102mm5mm. The size of main body is 156mm93mm45mm.
The size of square hole installed on the equipment cabinet is 156mm93mm. The front of the product is 17 user keys and 1 4.3and 480272 LSD (Liquid Crystal Display), and the reverse side is input signal, spindle control, stepper/ servo control, MPG and other four sets of interfaces as well as USB interface and power interface. Please look at the reference picture 1-3 and picture 1-4 in detail.
This USB Interface is the standard USB socket of A-type, attached a 50cm USB extension cord with installation lugs. Pendant Handwheel with Emergency stop. CNC system and position control of various mechanical devices, mainly for CNC machine tools and various mechanical zero correction and signal division. 100 times per revolution slightly cracking point, 100 pulses per revolution output, holding the handle of the panel and all-metal high-grade design. Metal code disc, high precision, good texture.
Easy installation, shaped thin, ultra-light. Voltage, single-ended, differential in three output options provide 100PPR pulse output options.Driver output type, anti-interference ability, long-distance transmission. Oil, water, dust-proof design (grade IP65) spiral stretch 20 million guaranteed. Novelty, easy to move, interference, load capacity. Full plastic shell, insulation, high strength, anti-oil seal design.
With × 1, × 10, × 100 third gear ratio, enabling 4-12 axis magnification switch. With the control switch, emergency stop switch optional, easy to operate. For CNC machine tools, printing machinery, numerical control equipment. OFF, X, Y, Z, 4.This column shows the current coordinate value of X work piece. 99999.999+99999.999, the minimum jump value is 0.001. This column shows the current coordinate value of Y work piece. The display range is -99999.999+99999.999. The minimum jump value is 0.001. This column shows the current coordinate value of Zwork piece. 4A CoordinateThis section has no definition in the 3-axis.
This column shows the current coordinate value of Z work piece. This section has no definition in the 3-axis. When this column performs the G codefile, it will show the current operation line number and codes. Operation state is REDAY, it will show null. The page code instructs the current page.This controller totally has 3 pages, including main page, file page and. This prompt message only has 3 status switching. Mainly it provides the prompt massage of several key. Buttons and the second functional operation function. The prompt message of the normal state is: normal mode.
The prompt message of the second functional start status is:X-: gotoz Y-: zero Z-: home A-: probe Start: goto. When the prompt message is in this status, knock on X-key to enter the goto zerofunction; knock on Y-to enter. The current coordinate 0 clearing function; knock on Z-to enter the search machinery 0-point function; knock on A- to. Enter the probe function; knock on Start to enter the designated staring function; knock on Pause to enter the breakpoint.
When it is in the designated line editing or in the required editing digital, the prompt message is:X+: leftX. Right Y+: Up Y-: Down Z-: enter Z+: cancel. When the prompt message is in this status, knock on X+ cursor to move left; knock on X- cursor to move right. Knock on current place value to increase; knock on Y- current place value to decrease; knock on Z- to enter or carriage.
Return; knock on Z+ to cancel. It can use FRO/ SROand then press the key to switch to this column, thus amendingthe current coordinate. The modification range is G54-G59. When shifts to this column, the words of G54 will change as bold type. It can use FRO/ SROand then press the key to switch to this column.
When it shifts to this column soft limit. The word ON will change to as bold type.At this time, please press the key to select whether to shift to. It can use the FRO/ SROand then the key switch to come to this column. When shifts to this column, the word. Of S will change as the bold type. The 0-position on the left will show the real speed of spindle.
Right will show the default speed of spindle. This default speed can be modified. When it shifts to this column, the word of.F will change as bold type. The place of 1182 on the left will show the real time feed rate, and the place of 2400 on the. Right will show the default feed rate. Manual adjust will change as bold type. At this time, please press the key A+ to increase the manual adjustsvalue. Andpress the key A- to decrease the manual adjusts value. Each step will increase or decrease 10%.
Spindle will change as bold type. At this time, please press the key A+ to increase the spindle adjusts value and press Ato decrease the spindle adjusts value. When it shifts to this column, the word of feed adjust will change as bold type. At this time, please press the key A+ to increase the feed adjusts value and press.A- to decrease the feed adjusts value. This column shows the processing time from starting operating the G code timekeeping to the stop of. It will also pause in the midway of pause time. This column shows the processing files. In the formal situation, it only shows the filename. Of CONT adjust, it will also show the content of the file. This column shows the operating status of equipment. The status and implications can be displayed as follows. Busy: In the process of processing status, manual operating single-axis status and other arbitrary axis status.
Reset: The reset flashing indicates to enter the reset status. At this time, any other keys dont work. REDAY: Ready state; when it is in the state of reset, you can press the reset key to enter the REDAY status. This time, it can operate and execute the automatic processing or modify other parameters and other operations.
This column shows the feed status of equipment. Automatic: in the process of processing and executing the G code file status, and displaying AUTO.
At this time, please press and hold the key-or + of XYZA, which can make each. Step: indicates runs step by step. At this time, please knock on the key-or + of XYZA, which can make. Each axis to move 1-unit distance and this unit distance can be modified in manual adjust parameter.
Hold these keys, you can only make each axis to operate 1-unit distance. This function can be used in accurate. MPG: indicates to enter the MPG mode. At this time, the MPG is invalid.The position of each axis can be. 2nd mode; When you press this key, you can enter the second function status. At this time, the status line will.
Please check out your address carefully when processing order. We are not responsible for wrong or undeliverable address. 1530 workings days to most other countries. When you have the parcel, and not satisfied the goods or it is other problem like as broken, pls tell us the detail reason and provide the photos, we will help you to solve any problems.
We work hard to make sure EVERY CUSTOMER 100% satisfaction. The item "Ger 4 Axis 3.1 Stand alone Motion Offline CNC Controller System +MPG Handwheel" is in sale since Wednesday, April 14, 2021.
This item is in the category "Business & Industrie\Automation, Antriebe & Motoren\Elektromotoren\Schrittmotoren". The seller is "powace1515" and is located in Prague. This item can be shipped to European Union member countries.